Advanced Functional Materials and Devices (AFMD) Group

Abstract:

The interplay of light absorption, charge-carrier transport, and charge-carrier recombination determines the performance of a photovoltaic absorber material. Here we analyze the influence on the solar-cell efficiency of the absorber material properties absorption coefficient α, charge-carrier mobility μ, and charge-carrier lifetime τ, for different scenarios. We combine analytical calculations with numerical drift-diffusion simulations to understand the relative importance of these three quantities. Whenever charge collection is a limiting factor, the αμτ product is a good figure of merit (FOM) to predict solar-cell efficiency, while for sufficiently high mobilities, the relevant FOM is reduced to the ατ product. We find no fundamental difference between simulations based on monomolecular or bimolecular recombination, but strong surface-recombination affects the maximum efficiency in the high-mobility limit. In the limiting case of high μ and high surface-recombination velocity S, the α/S ratio is the relevant FOM. Subsequently, we apply our findings to organic solar cells which tend to suffer from inefficient charge-carrier collection and whose absorptivity is influenced by interference effects. We estimate that a modest increase in absorption strength by a factor of 1.5 leads to a relative efficiency increase of more than 10% for state-of-the-art organic solar cells.

Abstract:

This journal is © The Royal Society of Chemistry. The quenching of excitons in organic solar cells can play a significant role in limiting their power conversion efficiency (PCE). In this article, we investigate the effect of a thin layer of hexapropyltruxene inserted at the interface between the electron donor boron subphthalocyanine chloride (SubPc) and its underlying hole contact in planar heterojunction solar cells. We find that a 3.8 nm hexapropyltruxene interlayer between the molybdenum oxide (MoOx) hole contact and SubPc is sufficient to improve PCE in SubPc/C60 fullerene solar cells from 2.6% to 3.0%, a ∼20% performance improvement. While the absorption stays roughly the same, the comparison of external and internal quantum efficiencies reveals a significant increase in SubPc's contribution to the current for light with wavelengths between 520 and 600 nm. Microstructure and surface morphology assessed with in situ Grazing-Incidence Wide-Angle X-Ray Scattering (GIWAXS) and Atomic Force Microscopy (AFM), are evaluated alongside in situ spectroscopic ellipsometry, and photoluminescence measurements. The microstructural investigations demonstrate changes to the surface and bulk of SubPc grown atop a hexapropyltruxene interlayer indicating that the latter acts as a template layer in a similar way as MoOx. However, the improvement in PCE is found to be mainly via reduced exciton quenching at the MoOx contact with the insertion of the hexapropyltruxene layer.

Abstract:

Previous theoretical calculations show azetidinium has the right radial size to form a 3D perovskite with lead halides [1], and has been shown to impart, as the A-site cation of ABX3 unit, beneficial properties to ferroelectric perovskites [2]. However, there has been very limited research into its use as the cation in lead halide perovskites to date. In this communication we report the synthesis and characterization of azetidinium-based lead mixed halide perovskite colloidal nanocrystals. The mixed halide system is iodine and chlorine unlike other reported nanocrystals in the literature where the halide systems are either iodine/bromine or bromine/chlorine. UV-visible absorbance data, complemented with photoluminescence spectroscopy, reveals an indirect-bandgap of about 1.96 eV for our nanocrystals. Structural characterization using TEM shows two distinct interatomic distances (2.98 +/- 0.15 Angstroms and 3.43 +/- 0.16 Angstroms) and non-orthogonal lattice angles (approximately 112 degrees) intrinsic to the nanocrystals with a probable triclinic structure revealed by XRD. The presence of chlorine and iodine within the nanocrystals is confirmed by EDS spectroscopy. Finally, light-induced electron paramagnetic resonance (LEPR) spectroscopy with PCBM confirms the photoinduced charge transfer capabilities of the nanocrystals. The formation of such semiconducting lead mixed halide perovskite using azetidinium as the cation suggests a promising subclass of hybrid perovskites holding potential for optoelectronic applications such as in solar cells and photodetectors.

Abstract:

We report two donor–acceptor (D–A) materials based on a cyanoanthracene acceptor paired with diphenylamine (DPAAnCN) and carbazole (CzAnCN) donor moieties. These compounds show hybrid locally excited (LE) charge-transfer (CT) excited states (HLCT), which we demonstrated through a combined photophysical and computational study. Vacuum-deposited organic light emitting diodes (OLEDs) using these HLCT emitters exhibit maximum external quantum efficiencies (EQE_max) close to 6%, with impressive exciton utilization efficiency (Φ_s) of >50%, far exceeding the spin statistic limit of 25%. We rule out triplet–triplet annihilation and thermally activated delayed fluorescence as triplet harvesting mechanisms along with horizontal orientation of emitters to enhance light outcoupling and, instead, propose a “hot exciton” channel involving the nearly isoenergetic T₂ and S₁ states.