Prof Henry Snaith FRS

Abstract:

Vacuum-based deposition is a scalable, solvent-free industrial method ideal for uniform coatings on complex substrates. However, all vacuum-deposited perovskite solar cells fabricated by thermal evaporation trail solution-processed counterparts in efficiency and stability due to film quality challenges, necessitating advancement and improved understanding. Here, we report a co-evaporation route for 1.67-eV wide-bandgap perovskites by introducing a PbCl2 co-source to optimize film quality. We promote perovskite formation with pronounced (100) “face-up” orientation and deliver a certified all vacuum-deposited solar cell with 18.35% efficiency (19.3% in the lab) for 0.25-cm2 devices (18.5% for 1-cm2 cells). These cells retain 80% of peak efficiency after 1,080 hours under the ISOS-L-2 protocol. Leveraging operando hyperspectral imaging, we provide spatiotemporal spectral insight into halide segregation and trap-mediated recombination, correlating microscopic luminescence features with macroscopic device performance while distinguishing radiative from non-ideal recombination channels. We further demonstrate 27.2%-efficient 1-cm2 evaporated perovskite-on-silicon tandems and outdoor stability of all vacuum-deposited tandems in Italy, retaining ~80% initial performance after 8 months.

Abstract:

The anisotropy of perovskite nanoplatelets (PeNPLs) opens up many opportunities in optoelectronics, including enabling the emission of linearly polarized light. But the limited stability of PeNPLs is a pressing challenge, especially for red-emitting CsPbI3. Herein, we address this limitation by alloying formamidinium (FA) into the perovskite cuboctahedral site. Unlike Cs/FA alloying in bulk thin films or nanocubes, FA incorporation in nanoplatelets requires meticulous control over the reaction conditions, given that nanoplatelets are obtained in kinetically-driven growth regimes instead of thermodynamically-driven conditions. Through in-situ photoluminescence (PL) measurements, we find that excess FA leads to uncontrolled growth, where phase impurities and nanoplatelets of multiple thicknesses co-exist. Restricting the FA content to up to 25% Cs substitution enables monodisperse PeNPLs, and increases the PL quantum yield (from 53% to 61%), exciton lifetime (from 18 ns to 27 ns), and stability in ambient air (from ~2 days to >7 days) compared to CsPbI3. This arises due to hydrogen bonding between FA and the oleate and oleylammonium ligands, anchoring them to the surface to improve optoelectronic properties and stability. The reduction in non-radiative recombination, improvement in the nanoplatelet aspect ratio, and higher ligand density lead to FA-containing PeNPLs more effectively forming edge-up superlattices, enhancing the PL degree of linear polarization from 5.1% (CsPbI3) to 9.4% (Cs0.75FA0.25PbI3). These fundamental insights show how the stability limitations of PeNPLs could be addressed, and these materials grown more precisely to improve their performance as polarized light emitters, critical for utilizing them in next-generation display, bioimaging, and communications applications.

Abstract:

Perovskite inks play critical roles in determining film quality and device performance, and ink stability is desired to ensure high device reproducibility. Here, we reveal the instability issue of current cesium-formamidinium lead triiodide (CsxFA1-xPbI3) inks whose aggregation and precipitation tendencies are induced by excessively strong solvent-lead-halide coordination. By modulating coordination strength between precursor salts and solvents, we identify solvent coordination-dispersion equilibrium as the governing factor for ink stability and develop a stable ink that exhibits a remarkable increase in the shelf life. It effectively tunes ink drying and film crystallization, resulting in blade-coated perovskite films with excellent uniformity and low defect density. This enhancement led to increased aperture efficiency of ambient-fabricated p-i-n perovskite modules to 23.5%. The resultant devices also exhibit high durability, and 99% of the initial PCE was retained after 1700 hours of maximum power point tracking following the ISOS-L-2 standard protocol.

Abstract:

In mixed-halide perovskites, halide segregation results in rapid funnelling of charge carriers to the I-rich phase, increasing radiative recombination and slightly lowering their mobility, while sustaining effective charge-carrier extraction pathways. Mixed-halide perovskites offer ideal bandgaps for tandem solar cells, but they suffer from light-induced halide segregation, which compromises their operational stability. Here, we directly probe the impact of halide segregation on charge-carrier dynamics at the interface between a mixed-halide perovskite and charge transport layers by using a free-space synchronous multimodal spectroscopy approach, combining time-resolved microwave conductivity, time-resolved photoluminescence (PL) and steady-state PL. We present a method to distinguish directly between charge-carrier dynamics dominated by either majority or minority carriers, enabling us to isolate effects arising from charge-selective extraction from the perovskite to commonly used hole- or electron transport layers, i.e. poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) and SnO 2 , respectively. We show that halide segregation creates iodide-rich phases that capture charge carriers within sub-nanoseconds, which slightly reduces their mobilities at microwave frequencies. We reveal that charge extraction from such iodide-rich domains is still surprisingly feasible, but competes with enhanced radiative recombination resulting from higher charge concentrations caused by funnelling into these minority phases. We demonstrate that together such effects reduce charge diffusion lengths and can account for the widely observed reduction in open-circuit voltages and short-circuit currents in solar cells under operational conditions. Our findings unravel the causes underpinning the adverse impact of halide segregation and provide guidelines to improve device performance.

Abstract:

Perovskite solar cells (PSCs) are emerging as a particularly promising technology to enhance the world’s renewable energy generation capacity. As PSCs are transitioning from research to industrial-scale production, there is an important opportunity to establish sustainable manufacturing pathways. Here, we present a closed-loop framework for the development of environmentally sustainable PSCs and highlight strategies to achieve this vision. First, we analyse the sourcing of raw materials and compare two established PSC fabrication techniques, vapour-phase deposition and solution processing, evaluating their respective advantages and limitations in terms of economic feasibility and environmental impact. Second, we examine solution processing methods, focusing on solvent system design for the preparation of high-quality perovskite films and on the use of non-hazardous or less-hazardous solvents. Third, we examine potential lead-release concerns during PSC operation and discuss approaches to minimize associated environmental risks. Fourth, we summarize effective recycling methods for main PSC components to support a circular production model. Finally, we identify key challenges and outline future research directions to achieve fully sustainable, closed-loop PSC technologies.